Request Information
PUI Audio?'s ASE02506MS-LW90-DSM-R is a Dynamic Speaker Management (DSM)-Ready micro speaker that has been pre-characterized for use with Maxim's DSM smart amplifier solution. This DSM-Ready micro speaker comes prepackaged in a compact enclosure enabling easy system integration. This turnkey solution vastly increases the loudness (SPL) and bass response safely and reliably within our strict speaker specifications.

Simply load the provided Vdrx, defined as the voltage required to reach maximum excursion, into Maxim's DSM Sound Studio GUI when setting the excursion limit in the "Characterize" section of the GUI. You are now ready to start tuning! The DSM Sound Studio GUI allows you to develop a complete register map to customize DSM for your design.
Unit of Measure

Specifications

Available

 N/A {0}

Manufacturer Stock

 N/A {0}

Brands

 N/A PUI Audio™

Manufacturer

 N/A PUI Audio�, Inc.

Rated Power Handling

 N/A 1 W

Maximum Power Handling

 N/A 1.2 W

Impedance at 2 Kilohertz (kHz) Frequency

 N/A 6 Ω

Impedance Tolerance (±) at 2 Kilohertz (kHz) Frequency

 N/A 15 %

Sensitivity

 N/A 93 dB

Sensitivity Tolerance (±)

 N/A 3 dB

Testing Condition for Sensitivity

 N/A Sound Pressure Level (SPL) at 2.45 V/10 cm
At 2 kHz in 1cc enclosure

Resonant Frequency (Free Air)

 N/A 550 Hz

Resonant Frequency (Free Air) Tolerance (±)

 N/A 10 %

Resonant Frequency in 1.5 Cubic Centimeter (cm³) Enclosure

 N/A 750 Hz

Resonant Frequency Tolerance (±) in 1.5 Cubic Centimeter (cm³) Enclosure

 N/A 10 Hz
Frequency Range1 N/A 650 ~ 20000 Hz
Xmax2 N/A 0.3 mm

Maximum Voice Coil Temperature (Tmax)

 N/A 90 ºC
Vdrx3 N/A 3.65 V

Housing Material

 N/A Acrylonitrile Butadiene Styrene (ABS)

Magnet Material

 N/A Neodymium (NdFeB)

Polarity

 N/A With positive voltage applied to the positive terminal, the diaphragm will move outward.

Storage Temperature

 N/A -40 ~ +85 ºC

Operating Temperature

 N/A -20 ~ +70 ºC

Ingress Protection Rating

 N/A Ingress Protection (IP67)

Size

 N/A 25 mm

Tolerance (±)

 N/A 0.2 mm

Angle Tolerance (±)

 N/A 3 º

Weight

 N/A 15 g

Industry Standards

 N/A Restriction of Hazardous Substances (RoHS) 2011/65/EU

Reliability Testing

High Temperature Test

 N/A 96 hours at +85 ºC ± 3 ºC followed by three hours in normal room temperature

Low Temperature Test

 N/A 96 hours at -40 ºC ± 3 ºC followed by three hours in normal room temperature

Humidity Test

 N/A 96 hours at +40 ºC ± 3 ºC with relative humidity at 90% ~ 95% followed by 6 hours in normal room temperature

Temperature Cycle Test

 N/A The part shall be subjected to 12 cycles using the following procedure:
Low temperature: -40 ºC±3 ºC
High temperature:+80 ºC±3 ºC
Cycle: 2 hours at High, 5 minutes High to Low, 2 hours at Low, 5 minutes Low to High

Vibration Test

 N/A 10-55 to 10 Hz sine sweep, per minute at 1.5 mm amplitude 2 hours in each axis X, Y, and Z.

Drop Test

 N/A Mount speaker to 100 g fixture, drop fixture 1.5 meters, twice per side and twice for each corner.

Load Test

 N/A White noise is applied at the speakers rated power for 96 hours at room temperature with speaker in 1 cc enclosure.

Note for Reliability Testing

 N/A After each test, the speaker's SPL shall be ±3 dB of the original SPL.

Additional Information

Additional Information

 N/A DSM-Ready speaker + DSM Smart Amplifier delivers the easiest and fastest path for designing a high-performance speaker system in the shortest amount of time.

Note

Note

 N/A Specification subject to change or withdrawal without notice.
  • 1 -10 dB, without DSM
  • 2 Where BL product drops by 20%
  • 3 Based on Xmax set to 0.3 mm