Unit of Measure

Specifications

Available

N/A {0}

Manufacturer Stock

N/A {0}

Brands

N/A APEM

Manufacturer

N/A APEM

Series

N/A A01

Direct Current (DC) Rating

N/A 6 A

Agency Approvals

N/A Certified Residential Underwriter (CRU®) United States (US)

Note for Dimensions

N/A First dimensions are in mm while inches are shown in brackets. Refer to the following pages for further information.

Mounting Accessories

N/A Standard hardware 1 nut and 1 sealing washer.

Accessories

N/A Flap guards
Aluminum bezel protection guards
Anti rotation ring
Blanking plugs

Electrical Specifications

Minimum Alternating Current (AC) Current

N/A 10 mA

Minimum Alternating Current (AC) Voltage

N/A 5 V

Alternating Current (AC) Rating

N/A 6 A

Alternating Current (AC) Voltage

N/A 250 V

Direct Current (DC) Voltage

N/A 12 V

Maximum Initial Contact Resistance at 1 Ampere (A) Current and 4 Volts (V) Direct Current (DC) Voltage

N/A 10 mΩ

Minimum Insulation Resistance

N/A 50 MΩ

Dielectric Strength

N/A 750 V between open contacts, 5 KV live to accessible

Minimum Electrical Life

N/A 50000 cycles

Contact Gap

N/A >1 mm0.039 in

Insulation

N/A Class 2

Lamp Life

N/A LED, 60,000 hours to 75% relative luminosity filament, approx. 5000 hours neon, approx. 10,000 hours

Mechanical Specifications

Mechanical Life (Operator)

N/A Momentary, 1 million cycles, maintained 100,000 cycles

Lamp

N/A Midget Grove T1 3/4 Filament, Neon or Light-Emitting Diode (LED)

Solder/Quick Connect Terminals

N/A 2.8 mm0.11 in

General Specifications

Operating Temperature Range

N/A -20 to 55 ºC

Solder Heat Resistance for 5 Seconds (s)

N/A 350 ºC

Sealing

N/A Panel sealed to Internet Protocol (IP65), Rear of Panel Internet Protocol (IP40)

Materials

Screen Material

N/A Polycarbonates (PC)

Reflector Assembly Material

N/A Polycarbonates (PC)

Operator Material

N/A Polybutylene Terephthalate (PBT)

Nut Material

N/A Acrylonitrile Butadiene Styrene (ABS)

Camtrack Momentary Material

N/A Polyphenylene Ether (PPE)

Camtrack Maintained

N/A Polyphenylsulfone (PPSU)

Switch Block 1 and 2 Pole Material

N/A Polybutylene Terephthalate (PBT)

Switch Block 3 and 4 Pole Material

N/A Polyetherimide (PEI)

Contacts Material

N/A Gold-Plated Silver

Installation Guide

Installation Guide

N/A Panel Mounting Assembly
  • Drill/punch hole shaped as shown on page one.
  • Assemble front operator through hole, fit fixing nut and tighten to a maximum torque of 0.8 Nm using tool No. 30-0001.
  • Wire chosen switch block as required and slide onto operator until latch engages.
  • Fit bulb if required using tool No. 30-0002.
  • Snap screen onto reflector assembly with legend in between if required and snap onto front operator, take care to line up the locating slot with the polarizing dot and not to damage the internal seal
  • To place/remove the bulb use the bulb extractor 30-0002.
Switch Block Assembly

To assemble switch block to the operator, firstly, take care to line up the switch block with the back of the operator.
Once in position slide on to the back of the operator. N.B. Ensure latch is fully engaged correctly onto the switch block. To remove switch block, depress the latch and slide the switch block off the operator.

Distinctive Features

Distinctive Features

N/A
  • Panel Sealed to IP65
  • Single pole to four pole changeover
  • Custom engraving or film legends options
  • Push on tab terminals

Note

Note

N/A The company reserves the right to change specifications without notice.