Print Back
Unit of Measure

Specifications

Available

Manufacturer Stock

Brands

APEM

Manufacturer

APEM

Series

A01

Direct Current (DC) Rating

6 A

Agency Approvals

Certified Residential Underwriter (CRU®) United States (US)

Note for Dimensions

First dimensions are in mm while inches are shown in brackets. Refer to the following pages for further information.

Mounting Accessories

Standard hardware 1 nut and 1 sealing washer.

Accessories

Flap guards
Aluminum bezel protection guards
Anti rotation ring
Blanking plugs

Electrical Specifications

Minimum Alternating Current (AC) Current

10 mA

Minimum Alternating Current (AC) Voltage

5 V

Alternating Current (AC) Rating

6 A

Alternating Current (AC) Voltage

250 V

Direct Current (DC) Voltage

12 V

Maximum Initial Contact Resistance at 1 Ampere (A) Current and 4 Volts (V) Direct Current (DC) Voltage

10 mΩ

Minimum Insulation Resistance

50 MΩ

Dielectric Strength

750 V between open contacts, 5 KV live to accessible

Minimum Electrical Life

50000 cycles

Contact Gap

>1 mm0.039 in

Insulation

Class 2

Lamp Life

LED, 60,000 hours to 75% relative luminosity filament, approx. 5000 hours neon, approx. 10,000 hours

Mechanical Specifications

Mechanical Life (Operator)

Momentary, 1 million cycles, maintained 100,000 cycles

Lamp

Midget Grove T1 3/4 Filament, Neon or Light-Emitting Diode (LED)

Solder/Quick Connect Terminals

2.8 mm0.11 in

General Specifications

Operating Temperature Range

-20 to 55 ºC

Solder Heat Resistance for 5 Seconds (s)

350 ºC

Sealing

Panel sealed to Internet Protocol (IP65), Rear of Panel Internet Protocol (IP40)

Materials

Screen Material

Polycarbonates (PC)

Reflector Assembly Material

Polycarbonates (PC)

Operator Material

Polybutylene Terephthalate (PBT)

Nut Material

Acrylonitrile Butadiene Styrene (ABS)

Camtrack Momentary Material

Polyphenylene Ether (PPE)

Camtrack Maintained

Polyphenylsulfone (PPSU)

Switch Block 1 and 2 Pole Material

Polybutylene Terephthalate (PBT)

Switch Block 3 and 4 Pole Material

Polyetherimide (PEI)

Contacts Material

Gold-Plated Silver

Installation Guide

Installation Guide

Panel Mounting Assembly
  • Drill/punch hole shaped as shown on page one.
  • Assemble front operator through hole, fit fixing nut and tighten to a maximum torque of 0.8 Nm using tool No. 30-0001.
  • Wire chosen switch block as required and slide onto operator until latch engages.
  • Fit bulb if required using tool No. 30-0002.
  • Snap screen onto reflector assembly with legend in between if required and snap onto front operator, take care to line up the locating slot with the polarizing dot and not to damage the internal seal
  • To place/remove the bulb use the bulb extractor 30-0002.
Switch Block Assembly

To assemble switch block to the operator, firstly, take care to line up the switch block with the back of the operator.
Once in position slide on to the back of the operator. N.B. Ensure latch is fully engaged correctly onto the switch block. To remove switch block, depress the latch and slide the switch block off the operator.

Distinctive Features

Distinctive Features

  • Panel Sealed to IP65
  • Single pole to four pole changeover
  • Custom engraving or film legends options
  • Push on tab terminals

Note

Note

The company reserves the right to change specifications without notice.