The eight ohm 18 mm x 13 mm AS01808AO-SC18-WP-R speaker is designed for high fidelity audio reproduction in the thinnest size possible-only 2.5 mm thick! Spring contacts offer quick electrical connection.
Unit of Measure
Specifications
Available |
N/A |
Manufacturer Stock |
N/A |
Brands |
N/A PUI Audio™ |
Manufacturer |
N/A PUI Audio�, Inc. |
Thickness |
N/A 2.5 mm |
Size |
N/A 18 x 13 mm |
Tolerance (±) |
N/A 0.5 mm |
Angle Tolerance (±) |
N/A 3 º |
Rated Input Power |
N/A 1 W |
Maximum Input Power |
N/A 1.2 W |
Impedance |
N/A 8 Ω |
Impedance Tolerance (±) |
N/A 15 % |
Sensitivity |
N/A 96 dB |
Sensitivity Tolerance (±) |
N/A 3 dB |
Testing Condition for Sensitivity |
N/A (Sound Pressure Level (SPL) at 2.83 V/10 cm) Avg 0.8, 1.0, 1.2, 1.5 kHz in 1 cc enclosure |
Resonant Frequency (Free Air) |
N/A 420 Hz |
Resonant Frequency (Free Air) Tolerance (±) |
N/A 20 % |
Frequency Range |
N/A Fo ~ 15000 Hz |
Buzz, Rattle, etc. |
N/A Should not be Audible with 2.83 V Sine Sweep from 500 Hz to 15 kHz Installed in a 1cc Enclosure |
Polarity |
N/A When Positive Voltage is Applied to the Positive Terminal, the Diaphragm will Move Outward |
Operating Temperature |
N/A -20 ~ +70 ºC |
Storage Temperature |
N/A -40 ~ +85 ºC |
Weight |
N/A 1.8 g |
Environmental Protection |
N/A Ingress Protection (IP65) |
Industry Standards |
N/A Restriction of Hazardous Substances (RoHS) 2011/65/EU |
Mechanical Reliability and Environment Testing
High Temperature Test |
N/A 96 hours at +85ºC ± 3ºC followed by two hours in normal room temperature |
Low Temperature Test |
N/A 96 hours at -40 ºC ± 3 ºC followed by two hours in normal room temperature |
Humidity Test |
N/A 96 hours at +55 ºC ± 3 ºC with relative humidity at 95% in accordance with IEC 68-2-67 |
Temperature Cycle Test |
N/A
The part shall be subjected to 20 cycles using the following procedure: Low temperature: -40ºC±3ºC High temperature:+85ºC±3ºC Cycle: 30 mins at High, 10 seconds High to Low, 30 mins at Low, 10 seconds minutes Low to High |
Vibration Test |
N/A
10-55 to 10 Hz sine sweep, per minute at 1.5 mm amplitude 2 hours in each axis X, Y, and Z |
Drop Test |
N/A Mount speaker to 150g fixture, drop fixture 1.5 meters onto marble surface 18 times total |
Load Test |
N/A DUTs shall be tested under each specified climatic condition for a continuous period of 100 hours at rated noise power. Speakers mounted in a 1cc back cavity; simulated program signal (IEC 268-1) with crest factor of 1.8 ~ 2.2 in rated frequency range; high pass 12dB/Oct or steeper, cut off at 850Hz. Refer to IEC 268-5 |
Note for Reliability Testing |
N/A After each test, the speaker's SPL shall be ±3 dB of the original SPL |
