Request Information
  • Radial Lead
  • Super low ESR, high temperature resistance
  • Large capacitance & Improved high ripple current capability
  • Suitable for DC-DC converters, voltage regulators and decoupling applications. For computer motherboards
  • Solvent resistant type
  • Halogen Free
Unit of Measure

Specifications

Available

 N/A 0

Manufacturer Stock

 N/A {0}

Brands

 N/A Nippon Chemi-Con

Manufacturer

 N/A United Chemi-Con

Series

 N/A NPCAP™-PS

Temperature Range

 N/A -55 to +105 ºC

Working Direct Current (DC) Voltage

 N/A 16 V

Capacitance

 N/A 180 µF

Capacitance Tolerance (±) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 20 %

Maximum Equivalent Series Resistance (ESR) at 100 to 300 Kilohertz (kHz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 16 mΩ

Rated Ripple Current at 105 Degree Celsius (ºC) Temperature, 100 Kilohertz (kHz) Frequency

 N/A 4360 mArms

Surge Voltage at 105 Degree Celsius (ºC) Temperature

 N/A Rated voltage x 1.15
Leakage Current at 20 Degree Celsius (ºC) Temperature After 2 Minutes1 N/A I=0.2CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (Vdc)

Maximum Dissipation Factor (Tan δ) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 0.12

Maximum Impedance Ratio Low Temperature Characteristics at 100 Kilohertz (kHz) Frequency

 N/A Z(-25 ºC)/Z(+20 ºC) ≤1.15
Z(-55 ºC)/Z(+20 ºC) ≤1.25

Endurance at 105 Degree Celsius (ºC) Temperature

 N/A 15000 hours

Failure Rate

 N/A 0.5% per 1,000 hours maximum (Confidence level 60% at 105 ºC)

Industry Standards

 N/A Restriction of Hazardous Substances (RoHS) Compliant

Dimensions

Diameter (D)

 N/A 8 mm

Maximum Diameter (D)

 N/A 8.5 mm

Dimension L

 N/A 11.5 mm

Maximum Dimension L

 N/A 13 mm

Diameter (d)

 N/A 0.6 mm

Dimension F

 N/A 3.5 mm

Endurance

Endurance

 N/A

The following specifications shall be satisfied when the capacitors are restored to 20 ºC after the rated voltage is applied for 15,000 hours at 105 ºC.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ The initial specified value

Bias Humidity Test

Bias Humidity Test

 N/A

The following specifications shall be satisfied when the capacitors are restored to 20 ºC after subjecting them to DC voltage at 60 ºC, 90 to 95% RH for 1,000 hours.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ The initial specified value

Surge Voltage Test

Surge Voltage Test

 N/A

The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 ºC for 30 seconds through a protective resistor (R=1 kΩ) and discharge for 5 minutes 30 seconds.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value

Note

Note

 N/A

Product specifications are subject to change without notice. Request our product specifications before purchase and/or use. Please use our products based on the information product specifications.
  • 1 If any doubt arises, measure the leakage current after the following voltage treatment.
    Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105 ºC.