Request Information
  • Surface Mount
  • Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte
  • Suitable for DC-DC converters, voltage regulators and decoupling applications used on computer motherboards etc.
  • Solvent resistant type
  • Halogen Free
Unit of Measure

Specifications

Available

 N/A 0

Manufacturer Stock

 N/A {0}

Brands

 N/A Nippon Chemi-Con

Manufacturer

 N/A United Chemi-Con

Series

 N/A NPCAP™-PXA

Temperature Range

 N/A -55 to +105 ºC

Working Direct Current (DC) Voltage

 N/A 16 V

Capacitance

 N/A 330 µF

Capacitance Tolerance (±) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 20 %

Maximum Equivalent Series Resistance (ESR) at 100 to 300 Kilohertz (kHz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 14 mΩ

Rated Ripple Current at 105 Degree Celsius (ºC) Temperature, 100 Kilohertz (kHz) Frequency

 N/A 5050 mArms
Maximum Leakage Current at 20 Degree Celsius (ºC) Temperature After 2 Minutes1 N/A 1050 µA

Maximum Dissipation Factor (Tan δ) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 0.12

Maximum Impedance Ratio Low Temperature Characteristics at 100 Kilohertz (kHz) Frequency

 N/A Z(-25 ºC)/Z(+20 ºC) ≤1.15
Z(-55 ºC)/Z(+20 ºC) ≤1.25

Failure Rate

 N/A 0.5% per 1,000 hours maximum (Confidence level 60% at 105 ºC)

Industry Standards

 N/A Restriction of Hazardous Substances (RoHS) Compliant

Dimensions

Diameter (D)

 N/A 10 mm

Dimension L

 N/A 12.5 mm

Dimension A

 N/A 10.3 mm

Dimension B

 N/A 10.3 mm

Dimension C

 N/A 11 mm

Dimension W

 N/A 0.7 to 1.1 mm

Dimension P

 N/A 4.5 mm

Rated Ripple Current Multipliers

Rated Ripple Current Multipliers at 120 Hertz (Hz) Frequency

 N/A 0.05

Rated Ripple Current Multipliers at 1 Kilohertz (kHz) Frequency

 N/A 0.30

Rated Ripple Current Multipliers at 10 Kilohertz (kHz) Frequency

 N/A 0.55

Rated Ripple Current Multipliers at 50 Kilohertz (kHz) Frequency

 N/A 0.70

Rated Ripple Current Multipliers at 100 to 500 Kilohertz (kHz) Frequency

 N/A 1

Endurance

Endurance

 N/A

The following specifications shall be satisfied when the capacitors are restored to 20 ºC after the rated voltage is applied for 15,000 hours (F45 : 3,000 hours) at 105 ºC.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ The initial specified value

Bias Humidity Test

Bias Humidity Test

 N/A

The following specifications shall be satisfied when the capacitors are restored to 20 ºC after subjecting them to DC voltage at 60 ºC, 90 to 95% RH for 1,000 hours.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ The initial specified value

Surge Voltage Test

Direct Current Surge Voltage (SVDC)

 N/A 18 V

Surge Voltage Test

 N/A

The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 ºC for 30 seconds through a protective resistor (R=1 kΩ) and discharge for 5 minutes 30 seconds.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value

Note

Note

 N/A

Product specifications are subject to change without notice. Request our product specifications before purchase and/or use. Please use our products based on the information product specifications.
  • 1 If any doubt arises, measure the leakage current after the following voltage treatment.
    Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105 ºC.