Projections Unlimited, Inc
PUI | Global Corporate HQ
15311 Barranca Parkway
Irvine , CA , 92618
United States
Phone:(714) 544-2700
Email: sales@gopui.com
Print Back
  • Downsizing and lower ESR, 2,000 hours at 105 ?C
  • Solvent resistant type
  • Vibration resistant structure
Unit of Measure

Specifications

Available

 N/A {0}

Manufacturer Stock

 N/A {0}

Brands

 N/A Nippon Chemi-Con

Manufacturer

 N/A United Chemi-Con

Series

 N/A Alchip™-MZR

Working Direct Current (DC) Voltage

 N/A 25 V

Capacitance

 N/A 220 µF

Capacitance Tolerance (±) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 20 %

Dissipation Factor (Tan δ)

 N/A 0.14

Maximum Equivalent Series Resistance (ESR) at 100 Kilohertz (kHz) Frequency, 20 Degree Celsius (ºC) Temperature

 N/A 0.160 Ω

Rated Ripple Current at 105 Degree Celsius (ºC) Temperature, 100 Kilohertz (kHz) Frequency

 N/A 600 mArms

Endurance at 105 Degree Celsius (ºC) Temperature

 N/A 2000 hours

Temperature Range

 N/A -55 to +105 ºC

Leakage Current at 20 Degree Celsius (ºC) Temperature After 2 Minutes

 N/A I=0.01CV or 3 µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)

Maximum Impedance Ratio Low Temperature Characteristics at 120 Hertz (Hz) Frequency

 N/A Z(-25 ºC)/Z(+20 ºC) = 2 Z(-40 ºC)/Z(+20 ºC) = 3 Z(-55 ºC)/Z(+20 ºC) = 3

Mounting Style

 N/A Vertical Surface Mount

Industry Standards

 N/A Restriction of Hazardous Substances (RoHS) Compliant

Dimensions

Dimension D

 N/A 6.3 mm

Dimension L

 N/A 7.7 mm

Dimension L Tolerance (±)

 N/A 0.5 mm

Dimension A

 N/A 6.6 mm

Dimension B

 N/A 6.6 mm

Dimension C

 N/A 7.2 mm

Dimension W

 N/A 0.5 to 0.8 mm

Dimension P

 N/A 1.9 mm

Endurance

Endurance

 N/A The following specifications shall be satisfied when the capacitors are restored to 20 ºC after the rated voltage is applied for2,000 hours at 105 ºC.

Capacitance change: ≤ ±30% of the initial value
D.F. (tan δ): ≤ 200% of the initial value
Leakage current: ≤ The initial specified value

Shelf Life

Shelf Life

 N/A The following specifications shall be satisfied when the capacitors are restored to 20 ºC after exposing them for 1,000 hours at 105 ºC without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.

Capacitance change: ≤ ±30% of the initial value
D.F. (tan δ): ≤ 200% of the initial value
Leakage current: ≤ The initial specified value

Surge Voltage Test

Surge Voltage Test

 N/A The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30±5 seconds through a protective resistor (as required for RC=0.1±0.05 sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35 ºC.

Surge Voltage: 29 V
Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ The initial specified value
ESR: ≤ 200% of the initial specified value
Leakage current: ≤ The initial specified value

Caution:
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions. It does not imply long-term use at all.

Note

Note

 N/A Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure.
A protection circuit should be used if applied voltage will exceed the rated voltages.

Please contact us for mass production schedule.
Specifications in this bulletin are subject to change without notice.