• Surface Mount
  • Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte
  • Suitable for DC-DC converters, voltage regulators and decoupling applications used on computer motherboards etc.
  • Solvent resistant type
  • Halogen Free
Unit of Measure

Specifications

Available

0

Manufacturer Stock

Brands

Nippon Chemi-Con

Manufacturer

United Chemi-Con

Series

NPCAP™-PXA

Temperature Range

-55 to +105 ºC

Working Direct Current (DC) Voltage

16 V

Capacitance

330 µF

Capacitance Tolerance (±) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

20 %

Maximum Equivalent Series Resistance (ESR) at 100 to 300 Kilohertz (kHz) Frequency, 20 Degree Celsius (ºC) Temperature

14 mΩ

Rated Ripple Current at 105 Degree Celsius (ºC) Temperature, 100 Kilohertz (kHz) Frequency

5050 mArms
Maximum Leakage Current at 20 Degree Celsius (ºC) Temperature After 2 Minutes1 1050 µA

Maximum Dissipation Factor (Tan δ) at 120 Hertz (Hz) Frequency, 20 Degree Celsius (ºC) Temperature

0.12

Maximum Impedance Ratio Low Temperature Characteristics at 100 Kilohertz (kHz) Frequency

Z(-25 ºC)/Z(+20 ºC) ≤1.15
Z(-55 ºC)/Z(+20 ºC) ≤1.25

Failure Rate

0.5% per 1,000 hours maximum (Confidence level 60% at 105 ºC)

Industry Standards

Restriction of Hazardous Substances (RoHS) Compliant

Dimensions

Diameter (D)

10 mm

Dimension L

12.5 mm

Dimension A

10.3 mm

Dimension B

10.3 mm

Dimension C

11 mm

Dimension W

0.7 to 1.1 mm

Dimension P

4.5 mm

Rated Ripple Current Multipliers

Rated Ripple Current Multipliers at 120 Hertz (Hz) Frequency

0.05

Rated Ripple Current Multipliers at 1 Kilohertz (kHz) Frequency

0.30

Rated Ripple Current Multipliers at 10 Kilohertz (kHz) Frequency

0.55

Rated Ripple Current Multipliers at 50 Kilohertz (kHz) Frequency

0.70

Rated Ripple Current Multipliers at 100 to 500 Kilohertz (kHz) Frequency

1

Endurance

Endurance

The following specifications shall be satisfied when the capacitors are restored to 20 ºC after the rated voltage is applied for 15,000 hours (F45 : 3,000 hours) at 105 ºC.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ The initial specified value

Bias Humidity Test

Bias Humidity Test

The following specifications shall be satisfied when the capacitors are restored to 20 ºC after subjecting them to DC voltage at 60 ºC, 90 to 95% RH for 1,000 hours.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ The initial specified value

Surge Voltage Test

Direct Current Surge Voltage (SVDC)

18 V

Surge Voltage Test

The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 ºC for 30 seconds through a protective resistor (R=1 kΩ) and discharge for 5 minutes 30 seconds.

Appearance: No significant damage
Capacitance change: ≤ ±20% of the initial value
D.F. (tan δ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value

Note

Note

Product specifications are subject to change without notice. Request our product specifications before purchase and/or use. Please use our products based on the information product specifications.

  • 1 If any doubt arises, measure the leakage current after the following voltage treatment.
    Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105 ºC.